|
Who's Online
There currently are 6043 guests online.
|
Categories
|
Information
|
Featured Product
|
|
|
|
|
There are currently no product reviews.
;
I ordered this manual sometime in the afternoon and I received it on my e-mail the same evening.
This is a fantastically good and properly scanned copy of the original manual. All pages are of the same scale and they overlap each other. It means that you can print the manual and easily make it as a convenient paper manual.
The content of the manual is fantastic. Alignment descriptions, PCB layouts and elementary diagrams are explicit and precise. I immediately found what I was looking for. Thanks to this manual and Owner-Manuals.com my amplifier is alive again. Many thanx indded!
;
The manual was well-scanned and easy to read. As an added bonus, the Operator's Manual was bundled with the Service Manual!
I'd definitely use owner-manuals.com again.
;
Finally, i found one website, where i can download this service manual , and fix my hifi. The service manual is very good, and easy to download and to print.
;
Complete and very useful. Could have benefited from a little higher resolution on the schematic and layout diagrams for improved legibility.
;
Great Service Manual, Very Complete, as advertised, Perfect, Thanks!
NVRAM
(ICf2)
Language selection 1. Press the MENU button (under the lid). 2. Select �Set-up� with the cursor buttons (up-/downwards) press the OK button. 3. Select �Language� and press the OK button. 4. Select the desired language and press the OK button. 5. Press the TV button to exit. Manual tuning I. Select programme number you want to tune. 2. Press the MENU button. 3. Select �Manual tuning� and press the OK button. 4. Press the red button (SEARCH). 5. Press the OK button to store. 6. Press the TV button to exit.
1
and
APSi (Automatic Programming System) 1. Press the MENU button. 2. Select �Set-up� and press the OK button. 3. Select �Retune TV� and press the OK button. 4. To retune the channels, press the OK button. 5. Press the TV button to exit.
lnitialization of NVRAM The NVRAM must be initialized and configured, if the NVRAM is replaced or it has totally lost its data. The next procedure is assuming that the tv does not start at all due to wrong data in NVRAM. 1. Set the receiver to the service mode by switching on the receiver with the mains switch and within 5 s. pressing the buttons MENU, TV and �7� successively. Note! The receiver is in the service mode although it looks like the receiver is in stand-by mode! 2. Press the RED-button to pre-configurate the set. Green led will flash once to indicate this. 3a At the same time the controller will check NVRAM and initializes it automatically if it was �empty�. lnitializing will take about 15s. When it is complet, the green led will light up. Continue to the step 4. 3b The automatic initializing did not happen, if the green led does not light up steady. In some cases the led might also light up immediately after configuration without any initializing, depending on NVRAM contents. In this case it might be enough to to store the new configuration by pressing �OK�. Continue to the step 4. 3c If the automatic initializing did not happen, you can start it manually by entering the key code: BLUE (wait approx. 2~1, 2,5,4 (wait approx. 2s) and OK. lnitializing will take about 15 s. 4. Switch off the receiver by pressing the mains switch. 5. Set the receiver to the service mode by switching on the receiver with the main switch and within 5 s. pressing the buttons MENU, TV and 7� successively. If the receiver remains in stand-by mode, press the TV button twice and then press the �7� button. 6. Configurate the receiver by pressing the RED button. The configuration menu will show up. 7. Press the OK button. 8. Press the TV-button and tune in one or more tv channels. 9. Return to service mode by pressing the �i� button. 10, After that make all of the service adjustments (see section �Service adjustments via IIC bus�). 11. Switch off the receiver by pressing the mains switch.
|
|
|
> |
|